Search Results

Search found 30514 results on 1221 pages for '10 04'.

Page 146/1221 | < Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >

  • Raid 5 with hot spare or RAID 10 with no hot spare?

    - by Boden
    Yes, this is on of those "do my job for me" questions, have some pity:) I'm at the limit for what I can do with the number of hard drives in a server without spending a substantial amount of money. I have four drives left to configure, and I can either set them up as a RAID 5 and dedicate a hot spare, or a RAID 10 with no hot spare. The size of each will be the same, and the RAID 5 will offer enough performance. I'm RAID 5 shy, but I also don't like the idea of running without a hot spare. I'm not so interested in degraded performance, but the amount of time the system is without adequate redundancy. The server and drives are under a 13x5 4 hour response contract (although I happen to know that the nearest service provider is at least 2-3 hours away by car in the winter). I should note that the server also has two RAID 1 arrays which would also be protected by the hot spare. Why don't they make drive cages with 9 bays! Heh.

    Read the article

  • Can't find partition tab in disk utility osX ver. 10.6.8

    - by John W
    I just got a used Mac Book Pro. I created a new admin account and deleted the old one as well as one other user. This is an older late 2007 MBP... the osX upgrade to 10.6.8 was just performed. My Macintosh HD is showing up as Partition 2. I ran disk utility (not from install disk), but there was no partition tab. I have a 160GB drive with only 53GB of space left on it. Since I am the only user and have no files on the laptop yet, I don't understand why there is so little space left. Surely the OS can't use up over 100GB. I wanted to run disk utility to see if there were any recovery partitions or other partition left over from the previous owner that could be erased to make room for expanding the main partition. Unfortunately, there is no partition tab in disk utility. The documentation I have found on line states that this version of osX includes that utility. The osX disks I have are for an older version so I wasn't sure if they would be of any use in solving this problem. Also, I was afraid if using the disks, would I lose the little bit of data/apps that I have assembled. I would rather not do a fresh install and have to do all the updates again to achieve this. The previous owner had some apps that I don't want to lose as I would have to pay handsomely to get them back. Simply, if all the previous users data is backed up on here after deleting user is still taking up space on a recovery partition (that I can't see)... I need to locate it erase it and expand the primary partition to re-aquire disk space for my files. I am new to Mac, so please be as descriptive as possible. Thanks.

    Read the article

  • Solaris 10: How to remove devices from a zpool with /usr currently mounted?

    - by cali-spc
    I use Solaris 10 on SPARC. I have /usr legacy mounted on a zpool 'usr-pool'. I now need to move some of the devices in usr-pool to another zpool which is running out of room. What is the safest way for me to do this? I already know that (since my zpool is not mirrored) I need to destroy and recreate the zpool. I know how to backup and restore a zfs snapshot. However... I'm stumped on how to unmount usr-pool without losing access to the commands I need on /usr to complete the backup/restore. Cursory research indicated that I should boot to OpenBoot (init 0) and then 'boot cdrom -s'. I did this but none of the zpools are accessible on that runlevel. I also read I could just copy /usr to another location, symlink /usr to that location, then do my backup/restore. Is that safe to do? I would appreciate some guidance. S.

    Read the article

  • 20 1TB drives vs. 10 2TB drives in RAID5/6 server

    - by Hunter
    Hi everyone, I will be setting up a server at work and I need some advice on some details. The setup will be one blade-type server (8-core, 16GB RAM) with two subsystems - one for the main storage the other to back it up. I'm shooting for a 20TB array (I know it'll be less after formatting and parity drives). So is there any advantage one way or the other with either 20 1TB drives or 10 2TB drives? I'm not sure right now how many controllers I should have either (in the quote I have is a dual-port controller). I would think two controllers for a server of this size would be a better choice than the dual-port controller (but I really don't know). And would an array of this size have any performance issues in RAID 5 or 6 (I know RAID 5 or 6 are "slower" because of all the parity calculations). Also, these will be either WD RE3 (1TB) or the RE4 (2TB). Oh, also, for the backup array would it be ok to use the WD 2TB green drives (also in RAID5 or 6)?

    Read the article

  • Cannot determine ethernet address for proxy ARP on PPTP

    - by Linux Intel
    I installed pptp server on a centos 6 64bit server PPTP Server ip : 55.66.77.10 PPTP Local ip : 10.0.0.1 Client1 IP : 10.0.0.60 centos 5 64bit Client2 IP : 10.0.0.61 centos5 64bit PPTP Server can ping Client1 And client 1 can ping PPTP Server PPTP Server can ping Client2 And client 2 can ping PPTP Server The problem is client 1 can not ping Client 2 and i get this error also on PPTP server error log Cannot determine ethernet address for proxy ARP Ping from Client2 to Client1 PING 10.0.0.60 (10.0.0.60) 56(84) bytes of data. --- 10.0.0.60 ping statistics --- 6 packets transmitted, 0 received, 100% packet loss, time 5000ms route -n on PPTP Server Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.60 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.0.61 0.0.0.0 255.255.255.255 UH 0 0 0 ppp1 55.66.77.10 0.0.0.0 255.255.255.248 U 0 0 0 eth0 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0 0.0.0.0 55.66.77.19 0.0.0.0 UG 0 0 0 eth0 route -n On Client 1 Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 55.66.77.10 70.14.13.19 255.255.255.255 UGH 0 0 0 eth0 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth1 0.0.0.0 70.14.13.19 0.0.0.0 UG 0 0 0 eth0 route -n On Client 2 Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 55.66.77.10 84.56.120.60 255.255.255.255 UGH 0 0 0 eth1 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth0 0.0.0.0 84.56.120.60 0.0.0.0 UG 0 0 0 eth1 cat /etc/ppp/options.pptpd on PPTP server ############################################################################### # $Id: options.pptpd,v 1.11 2005/12/29 01:21:09 quozl Exp $ # # Sample Poptop PPP options file /etc/ppp/options.pptpd # Options used by PPP when a connection arrives from a client. # This file is pointed to by /etc/pptpd.conf option keyword. # Changes are effective on the next connection. See "man pppd". # # You are expected to change this file to suit your system. As # packaged, it requires PPP 2.4.2 and the kernel MPPE module. ############################################################################### # Authentication # Name of the local system for authentication purposes # (must match the second field in /etc/ppp/chap-secrets entries) name pptpd # Strip the domain prefix from the username before authentication. # (applies if you use pppd with chapms-strip-domain patch) #chapms-strip-domain # Encryption # (There have been multiple versions of PPP with encryption support, # choose with of the following sections you will use.) # BSD licensed ppp-2.4.2 upstream with MPPE only, kernel module ppp_mppe.o # {{{ refuse-pap refuse-chap refuse-mschap # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. require-mschap-v2 # Require MPPE 128-bit encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) require-mppe-128 # }}} # OpenSSL licensed ppp-2.4.1 fork with MPPE only, kernel module mppe.o # {{{ #-chap #-chapms # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. #+chapms-v2 # Require MPPE encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) #mppe-40 # enable either 40-bit or 128-bit, not both #mppe-128 #mppe-stateless # }}} # Network and Routing # If pppd is acting as a server for Microsoft Windows clients, this # option allows pppd to supply one or two DNS (Domain Name Server) # addresses to the clients. The first instance of this option # specifies the primary DNS address; the second instance (if given) # specifies the secondary DNS address. #ms-dns 10.0.0.1 #ms-dns 10.0.0.2 # If pppd is acting as a server for Microsoft Windows or "Samba" # clients, this option allows pppd to supply one or two WINS (Windows # Internet Name Services) server addresses to the clients. The first # instance of this option specifies the primary WINS address; the # second instance (if given) specifies the secondary WINS address. #ms-wins 10.0.0.3 #ms-wins 10.0.0.4 # Add an entry to this system's ARP [Address Resolution Protocol] # table with the IP address of the peer and the Ethernet address of this # system. This will have the effect of making the peer appear to other # systems to be on the local ethernet. # (you do not need this if your PPTP server is responsible for routing # packets to the clients -- James Cameron) proxyarp # Normally pptpd passes the IP address to pppd, but if pptpd has been # given the delegate option in pptpd.conf or the --delegate command line # option, then pppd will use chap-secrets or radius to allocate the # client IP address. The default local IP address used at the server # end is often the same as the address of the server. To override this, # specify the local IP address here. # (you must not use this unless you have used the delegate option) #10.8.0.100 # Logging # Enable connection debugging facilities. # (see your syslog configuration for where pppd sends to) debug # Print out all the option values which have been set. # (often requested by mailing list to verify options) #dump # Miscellaneous # Create a UUCP-style lock file for the pseudo-tty to ensure exclusive # access. lock # Disable BSD-Compress compression nobsdcomp # Disable Van Jacobson compression # (needed on some networks with Windows 9x/ME/XP clients, see posting to # poptop-server on 14th April 2005 by Pawel Pokrywka and followups, # http://marc.theaimsgroup.com/?t=111343175400006&r=1&w=2 ) novj novjccomp # turn off logging to stderr, since this may be redirected to pptpd, # which may trigger a loopback nologfd # put plugins here # (putting them higher up may cause them to sent messages to the pty) cat /etc/ppp/options.pptp on Client1 and Client2 ############################################################################### # $Id: options.pptp,v 1.3 2006/03/26 23:11:05 quozl Exp $ # # Sample PPTP PPP options file /etc/ppp/options.pptp # Options used by PPP when a connection is made by a PPTP client. # This file can be referred to by an /etc/ppp/peers file for the tunnel. # Changes are effective on the next connection. See "man pppd". # # You are expected to change this file to suit your system. As # packaged, it requires PPP 2.4.2 or later from http://ppp.samba.org/ # and the kernel MPPE module available from the CVS repository also on # http://ppp.samba.org/, which is packaged for DKMS as kernel_ppp_mppe. ############################################################################### # Lock the port lock # Authentication # We don't need the tunnel server to authenticate itself noauth # We won't do PAP, EAP, CHAP, or MSCHAP, but we will accept MSCHAP-V2 # (you may need to remove these refusals if the server is not using MPPE) refuse-pap refuse-eap refuse-chap refuse-mschap # Compression # Turn off compression protocols we know won't be used nobsdcomp nodeflate # Encryption # (There have been multiple versions of PPP with encryption support, # choose which of the following sections you will use. Note that MPPE # requires the use of MSCHAP-V2 during authentication) # # Note that using PPTP with MPPE and MSCHAP-V2 should be considered # insecure: # http://marc.info/?l=pptpclient-devel&m=134372640219039&w=2 # https://github.com/moxie0/chapcrack/blob/master/README.md # http://technet.microsoft.com/en-us/security/advisory/2743314 # http://ppp.samba.org/ the PPP project version of PPP by Paul Mackarras # ppp-2.4.2 or later with MPPE only, kernel module ppp_mppe.o # If the kernel is booted in FIPS mode (fips=1), the ppp_mppe.ko module # is not allowed and PPTP-MPPE is not available. # {{{ # Require MPPE 128-bit encryption #require-mppe-128 # }}} # http://mppe-mppc.alphacron.de/ fork from PPP project by Jan Dubiec # ppp-2.4.2 or later with MPPE and MPPC, kernel module ppp_mppe_mppc.o # {{{ # Require MPPE 128-bit encryption #mppe required,stateless # }}} IPtables is stopped on clients and server, Also net.ipv4.ip_forward = 1 is enabled on PPTP Server. How can i solve this problem .?

    Read the article

  • Cisco ASA (Client VPN) to LAN - through second VPN to second LAN

    - by user50855
    We have 2 site that is linked by an IPSEC VPN to remote Cisco ASAs: Site 1 1.5Mb T1 Connection Cisco(1) 2841 Site 2 1.5Mb T1 Connection Cisco 2841 In addition: Site 1 has a 2nd WAN 3Mb bonded T1 Connection Cisco 5510 that connects to same LAN as Cisco(1) 2841. Basically, Remote Access (VPN) users connecting through Cisco ASA 5510 needs access to a service at the end of Site 2. This is due to the way the service is sold - Cisco 2841 routers are not under our management and it is setup to allow connection from local LAN VLAN 1 IP address 10.20.0.0/24. My idea is to have all traffic from Remote Users through Cisco ASA destined for Site 2 to go via the VPN between Site 1 and Site 2. The end result being all traffic that hits Site 2 has come via Site 1. I'm struggling to find a great deal of information on how this is setup. So, firstly, can anyone confirm that what I'm trying to achieve is possible? Secondly, can anyone help me to correct the configuration bellow or point me in the direction of an example of such a configuration? Many Thanks. interface Ethernet0/0 nameif outside security-level 0 ip address 7.7.7.19 255.255.255.240 interface Ethernet0/1 nameif inside security-level 100 ip address 10.20.0.249 255.255.255.0 object-group network group-inside-vpnclient description All inside networks accessible to vpn clients network-object 10.20.0.0 255.255.255.0 network-object 10.20.1.0 255.255.255.0 object-group network group-adp-network description ADP IP Address or network accessible to vpn clients network-object 207.207.207.173 255.255.255.255 access-list outside_access_in extended permit icmp any any echo-reply access-list outside_access_in extended permit icmp any any source-quench access-list outside_access_in extended permit icmp any any unreachable access-list outside_access_in extended permit icmp any any time-exceeded access-list outside_access_in extended permit tcp any host 7.7.7.20 eq smtp access-list outside_access_in extended permit tcp any host 7.7.7.20 eq https access-list outside_access_in extended permit tcp any host 7.7.7.20 eq pop3 access-list outside_access_in extended permit tcp any host 7.7.7.20 eq www access-list outside_access_in extended permit tcp any host 7.7.7.21 eq www access-list outside_access_in extended permit tcp any host 7.7.7.21 eq https access-list outside_access_in extended permit tcp any host 7.7.7.21 eq 5721 access-list acl-vpnclient extended permit ip object-group group-inside-vpnclient any access-list acl-vpnclient extended permit ip object-group group-inside-vpnclient object-group group-adp-network access-list acl-vpnclient extended permit ip object-group group-adp-network object-group group-inside-vpnclient access-list PinesFLVPNTunnel_splitTunnelAcl standard permit 10.20.0.0 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip 10.20.0.0 255.255.255.0 10.20.1.0 255.255.255.0 access-list inside_nat0_outbound_1 extended permit ip 10.20.0.0 255.255.255.0 host 207.207.207.173 access-list inside_nat0_outbound_1 extended permit ip 10.20.1.0 255.255.255.0 host 207.207.207.173 ip local pool VPNPool 10.20.1.100-10.20.1.200 mask 255.255.255.0 route outside 0.0.0.0 0.0.0.0 7.7.7.17 1 route inside 207.207.207.173 255.255.255.255 10.20.0.3 1 crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto dynamic-map outside_dyn_map 20 set security-association lifetime seconds 288000 crypto dynamic-map outside_dyn_map 20 set security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set reverse-route crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto map outside_dyn_map 20 match address acl-vpnclient crypto map outside_dyn_map 20 set security-association lifetime seconds 28800 crypto map outside_dyn_map 20 set security-association lifetime kilobytes 4608000 crypto isakmp identity address crypto isakmp enable outside crypto isakmp policy 20 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 group-policy YeahRightflVPNTunnel internal group-policy YeahRightflVPNTunnel attributes wins-server value 10.20.0.9 dns-server value 10.20.0.9 vpn-tunnel-protocol IPSec password-storage disable pfs disable split-tunnel-policy tunnelspecified split-tunnel-network-list value acl-vpnclient default-domain value YeahRight.com group-policy YeahRightFLVPNTunnel internal group-policy YeahRightFLVPNTunnel attributes wins-server value 10.20.0.9 dns-server value 10.20.0.9 10.20.0.7 vpn-tunnel-protocol IPSec split-tunnel-policy tunnelspecified split-tunnel-network-list value YeahRightFLVPNTunnel_splitTunnelAcl default-domain value yeahright.com tunnel-group YeahRightFLVPN type remote-access tunnel-group YeahRightFLVPN general-attributes address-pool VPNPool tunnel-group YeahRightFLVPNTunnel type remote-access tunnel-group YeahRightFLVPNTunnel general-attributes address-pool VPNPool authentication-server-group WinRadius default-group-policy YeahRightFLVPNTunnel tunnel-group YeahRightFLVPNTunnel ipsec-attributes pre-shared-key *

    Read the article

  • MPLS basic configuration

    - by Vineet Menon
    I want to test out MPLS VPN in my lab. I have 3 routers. 2 PEs and 1P router, all cisco 2921. Something like this, ----- ---- ----- | PE1 |.1____192.168.1.0____.2| P |.2____192.168.2.0____.1| PE2 | | | | | | | ----- ---- ----- lo0:10.1.1.1 lo0:10.1.1.2 lo0:10.1.1.3 Here's the configuration file for each of them, PE1 router hostname PE1 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! interface Loopback0 ip address 10.1.1.1 255.255.255.255 ! interface GigabitEthernet0/0 ip address 192.168.1.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.1.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.3 remote-as 100 neighbor 10.1.1.3 update-source Loopback0 neighbor 172.16.1.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.3 activate neighbor 10.1.1.3 send-community extended exit-address-family For P router: hostname P ! no ipv6 cef ip source-route ip cef ! interface Loopback0 ip address 10.1.1.2 255.255.255.255 ! interface GigabitEthernet0/1 ip address 192.168.1.2 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/2 ip address 192.168.2.2 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.2 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 ! For PE2 router: ! hostname PE2 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! ! interface Loopback0 ip address 10.1.1.3 255.255.255.0 ! interface GigabitEthernet0/0 ip address 192.168.2.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.2.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.3 0.0.0.0 area 0 network 192.168.2.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.1 remote-as 100 neighbor 10.1.1.1 update-source Loopback0 neighbor 172.16.2.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.1 activate neighbor 10.1.1.1 send-community extended exit-address-family ! I am following this article form cisco. But things are not working properly. Any help would be appreciated.

    Read the article

  • Excel on Mac Mini OS X Version 10.7.2 - Create text file named after a cell containing other cell data from other cells

    - by user143041
    I tried using the code below for the Excel program on my `Mac Mini using the OS X Version 10.7.2 and it keeps saying Error due to file name / path: (The Excel fiel I am creating is going to be a template with my formulas and macros installed which will be used over and over). Sub CreateFile() Do While Not IsEmpty(ActiveCell.Offset(0, 1)) MyFile = ActiveCell.Value & ".txt" fnum = FreeFile() Open MyFile For Output As fnum Print #fnum, ActiveCell.Offset(0, 1) & " " & ActiveCell.Offset(0, 2) Close #fnum ActiveCell.Offset(1, 0).Select Loop End Sub What Im trying to do: 1st Objective I would like to have the following data to be used to create a text file. A:A is what I need the name of the file to be. B:2 is the content I need in the text file. So, A2 - "repair-video-game-Glassboro-NJ-08028.txt" is the file name and B2 to be the content in the file. Next, A3 is the file name and B3 is the content for the file, etc. ONCE the content reads what is in cell A16 and B16 (length will vary), the file creation should stop, if not then I can delete the additional files created. This sheet will never change. Is there a way to establish the excel macro to always go to this sheet instead of have to select it with the mouse to identify the starting point? 2nd Objective I would like to have the following data to be used to create a text file. A:1 is what I need the name of the file to be. B:B is the content I want in the file. So, A2 - is the file name "geo-sitemap.xml" and B:B to be the content in the file (ignore the .xml file extension in the photo). ONCE the content cell reads what is in cell "B16" (length will vary), the file creation should stop, if not then I can adjust the cells that have need content (formulated content you see in the image is preset for 500 rows). This sheet will never change. Is there a way to establish the excel macro to always go to this sheet instead of have to select it with the mouse to identify the starting point? I can Provide the content in the cells that are filled in by excel formulas that are not not to be included in the .txt files. It is ok if it is not possible. I can delete the extra cells that are not populated (based on the data sheet). Please let me know if you need any more additional information or clarity and I will be happy to provide it. I really appreciate your help! Thank you

    Read the article

  • upgrading Subversion on Suse 10.0

    - by jessica
    I have a Suse Linux 10.0 with an old version of Subversion (1.4). I would like to upgrade it to the current (1.6.6) but I am having problem trying to understand how to build SVN from source. I mean, what should I pass to the configure script? Is there a simple way to upgrade the current SVN? thanks for the help. jessica

    Read the article

  • VPN Connection causes DNS to use wrong DNS server

    - by Bryan
    I have a Windows 7 PC on our company network (which is a member of our Active Directory). Everything works fine until I open a VPN connection to a customer's site. When I do connect, I lose network access to shares on the network, including directories such as 'Application Data' that we have a folder redirection policy for. As you can imagine, this makes working on the PC very difficult, as desktop shortcuts stop working, software stops working properly due to having 'Application Data' pulled from under it. Our network is routed (10.58.5.0/24), with other local subnets existing within the scope of 10.58.0.0/16. The remote network is on 192.168.0.0/24. I've tracked the issue down to being DNS related. As soon as I open the VPN tunnel, all my DNS traffic goes via the remote network, which explains the loss of local resources, but my question is, how can I force local DNS queries to go to our local DNS servers rather than our customers? The output of ipconfig /all when not connected to the VPN is below: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled This is the output of the same command with the VPN tunnel connected: Windows IP Configuration Host Name . . . . . . . . . . . . : 7k5xy4j Primary Dns Suffix . . . . . . . : mydomain.local Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mydomain.local PPP adapter Customer Domain: Connection-specific DNS Suffix . : customerdomain.com Description . . . . . . . . . . . : CustomerDomain Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.85(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.0.16 192.168.0.17 Primary WINS Server . . . . . . . : 192.168.0.17 NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : F0-4D-A2-DB-3B-CA DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::9457:c5e0:6f10:b298%10(Preferred) IPv4 Address. . . . . . . . . . . : 10.58.5.89(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 31 January 2012 15:55:47 Lease Expires . . . . . . . . . . : 10 February 2012 10:11:30 Default Gateway . . . . . . . . . : 10.58.5.1 DHCP Server . . . . . . . . . . . : 10.58.3.32 DHCPv6 IAID . . . . . . . . . . . : 250629538 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-14-AC-76-2D-F0-4D-A2-DB-3B-CA DNS Servers . . . . . . . . . . . : 10.58.3.32 10.58.3.33 NetBIOS over Tcpip. . . . . . . . : Enabled Routing table Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.58.5.1 10.58.5.89 20 10.58.5.0 255.255.255.0 On-link 10.58.5.89 276 10.58.5.89 255.255.255.255 On-link 10.58.5.89 276 10.58.5.255 255.255.255.255 On-link 10.58.5.89 276 91.194.153.42 255.255.255.255 10.58.5.1 10.58.5.89 21 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 192.168.0.95 192.168.0.85 21 192.168.0.85 255.255.255.255 On-link 192.168.0.85 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.58.5.89 276 224.0.0.0 240.0.0.0 On-link 192.168.0.85 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.58.5.89 276 255.255.255.255 255.255.255.255 On-link 192.168.0.85 276 The binding order for the interfaces is as follows: I've not configured the VPN tunnel to use the default gateway at the remote end, and network comms to nodes on both networks are fine. (i.e. I can ping any node on our network or the remote network). I've modified the PPTP connection properties to use the DNS servers 10.58.3.32 followed by 192.168.0.16, yet the query still goes to 192.168.0.16. Edit: The local resources that disappear are hosted on domain DFS roots, which might (or might not) be relevant.

    Read the article

  • Can't set up printing from Mac OS X (10.5.7) to an HP PSC 2410 shared from PC running Ubuntu 9.10

    - by Weston C
    I've got an HP PSC 2410 printer shared from a fresh Ubuntu 9.10 installation. I'm able to send documents to this printer over the network from another Ubuntu machine. But so far, I haven't been able to find a setup where I can send documents to that printer from a MacBook running 10.5.7. On the Mac side, when setting things up, I go into System Prefs Print & Fax, click on the "+" mark, select "IP", pick "IPP", enter the IP address of the Ubuntu box, leave the queue blank, enter the Name and location, and I think it's when I get to the "Print Using" (driver selection) part that I'm running into issues. If I use "Auto Select", it defaults to "Generic PostScript Printer", which I doubt the PSC 2410 is (and sure enough, if I print, the jobs don't go through). If I try "Select a driver to use...", there's not an option for an HP PSC 2400. This seems a little odd: I can plug the printer directly into one of our Macs and it immediately figures out the driver and I can print no problem, but that's apparently the way things work. So, that leaves one option: "Other", which, when selected, brings up a dialog apparently for the purpose of manually locating a driver. I've tried visiting HP's web site. They have drivers for earlier versions of Mac OS X, but state that after 10.4, Mac OS X should just come with the relevant drivers. I've also tried setting things up by interacting with the CUPS server on the Mac through a browser: I go to http://localhost:631/, select "Add New Printer", pick "Internet Printing Protocol (http)" for the Device selection, enter "http://ubuntu.machine.ip.address:631/printers/hp-psc-2400-series" for the Device URI, select "HP" for Make, and then on the next screen, we're back to the problem where the PSC 2400 just doesn't show up. There's an option to "provide a PPD file", which I assume would be the printer driver I can't find. A Google search for "HP PSC 2410 ppd Leopard" doesn't seem to yield much other than a reminder that the printer is supposed to just work out of the box on Leopard. A local search for ".ppd" or "2410" on either Mac also doesn't yield anything that looks like a relevant print driver. I'm totally stuck at this point. Any advice?

    Read the article

  • 10.6.4 Apple Wiki: New just created users can do nothing?

    - by beefon
    Hello, After update to 10.6.4 there's an issue: any new users that I create in Server Prefs/WGM can't post to their blogs, comment, create wiki pages... They can't do anything! There's log from Wiki errors (when user DURAK tries to create new blog entry): [HTTPChannel,5,127.0.0.1] Traceback (most recent call last): [HTTPChannel,5,127.0.0.1] File "/usr/share/caldavd/lib/python/twisted/web/server.py", line 126, in process self.render(resrc) [HTTPChannel,5,127.0.0.1] File "/usr/share/caldavd/lib/python/twisted/web/server.py", line 133, in render body = resrc.render(self) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_xmlrpc_server/WebAppServer.py", line 90, in render d = defer.maybeDeferred(function, *args) [HTTPChannel,5,127.0.0.1] File "/usr/share/caldavd/lib/python/twisted/internet/defer.py", line 104, in maybeDeferred result = f(*args, **kw) [HTTPChannel,5,127.0.0.1] --- <exception caught here> --- [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_xmlrpc_server/ContentServiceBase.py", line 121, in xmlrpc_addEntry aPage = ContentEntry.newBundleBasedContentEntry (path = path, content = content, author = author, title = title, uid = uid, type = kind, versioned = self.versioned, templateName = template) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_wlt/ContentEntry.py", line 794, in newBundleBasedContentEntry aPage.save('First created', 'created') [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_wlt/ContentEntry.py", line 445, in save revisions.addRevision(self.serializeEntry(revisionAttributes), inComment = comment, inAuthor = updateAuthor, inChangeType = editType) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_utilities/sqlitersion.py", line 36, in _func result = f(self, *args, **kwargs) [HTTPChannel,5,127.0.0.1] File "/usr/share/wikid/lib/python/apple_utilities/sqlitersion.py", line 49, in addRevision contentPlistStr = plistlib.writePlistToString(inContentDict).decode("utf-8") [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 110, in writePlistToString [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 94, in writePlist [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 251, in writeValue [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 280, in writeDict [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 238, in writeValue [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 171, in simpleElement [HTTPChannel,5,127.0.0.1] File "/S-m/Lib-ry/Fr-ks/Python.fr-k/Ver-s/2.6/lib/pyth-2.6/plistlib.py", line 221, in _escapeAndEncode [HTTPChannel,5,127.0.0.1] exceptions.UnicodeDecodeError: 'ascii' codec can't decode byte 0xd0 in position 0: ordinal not in range(128) [HTTPChannel,5,127.0.0.1] 'Unparseable html in page, removing whatever was already written.' [HTTPChannel,5,127.0.0.1] Removing /Library/Collaboration/Users/durak/weblog/27133.page Any "old" user CAN create, modify, comment, etc. What can you recommend to fix this issue? Hope for your help...

    Read the article

  • Networking is broken in my VMware 10.0 VMs after upgrading to Windows 8.1

    - by Michael Geary
    I have a VMware Workstation 10.0 installation with several virtual networks including the default host-only and NAT networks. After upgrading to Windows 8.1, the NAT network was not working. I booted an Ubuntu VM with the default network setup that was previously working, and it sat for a long time during startup saying it was waiting for the network. After it finally started up, an ifconfig showed no IP address for eth0. How can I fix the broken network?

    Read the article

  • Base 36 to Base 10 conversion using SQL only.

    - by EvilTeach
    A situation has arisen where I need to perform a base 36 to base 10 conversion, in the context of a SQL statement. There doesn't appear to be anything built into Oracle 9, or Oracle 10 to address this sort of thing. My Google-Fu, and AskTom suggest creating a pl/sql function to deal with the task. That is not an option for me at this point. I am looking for suggestions on an approach to take that might help me solve this issue. To put this into a visual form... WITH Base36Values AS ( SELECT '0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ' myBase36 FROM DUAL ), TestValues AS ( SELECT '01Z' BASE36_VALUE, 71 BASE10_VALUE FROM DUAL ) SELECT * FROM Base36Values, TestValues I am looking for something to calculate the value 71, based on the input 01Z. As a bribe, each useful answer gets a free upvote. Thanks Evil.

    Read the article

  • using Excel VBA, given the daily price of 50 stocks, choose 10 stocks such that they have the minumu

    - by correl
    The high-level goal is to choose 10 stocks that have the lowest correlation among one another, out of a pool of 50, so that I can have a well-diversified portfolio. I have managed to write some VBA macro to download the past 3 years of daily price data from Yahoo finance, and then compute the 50x50 correlation matrix (using the Correl function), using the daily close as the data. What I have tried so far is just some local-maximum heuristic: - For the two stocks that have the highest correlation with each other, remove one of them. Between the two, remove the one that has the higher average correlation with all the other stocks. - When I remove a stock from the pool, I just delete the correponding row and column, to give a smaller matrix. - Repeat until I have just 10 stocks remaining (a 10x10 matrix). I was wondering if there is some algorithm that already solves such a problem and gives the optimum solution?

    Read the article

  • Oracle Application Server 10.1.3.5 Security issue.

    - by Marius Bogdan IONESCU
    Hello! we are tying to port a J2EE app from OAS 9.0.4 (working perfectly) on OAS 10.1.3.5 the reson we do that is because we need the app compiled with java 1.5 and OAS 10.1.3.5 would be the single major version supporting that binaries which has oc4j/orion kernel. The issue is that the security constraints in matter of user/group/role are not read by the app server, and instead of asking for these sets of users, i have to use the oc4jadmin instead the selected users for auth. All xml files needed for describing these sets of rules are being checked with the OAS book, and it seems they are correctly filled in... anybody has an idea about this?

    Read the article

  • Flash 10 - read file from a drag and drop action?

    - by user246114
    Hi, I'm looking at how to read a file in flash 10 here: http://www.thedesilva.com/2008/11/flash-10-file-reference/ is there a way to initiate the file read from a drag and drop? For example, the user drags and drops a text file onto my flash element in the browser - can I initiate the file read from that? Thanks

    Read the article

  • What factors could cause the scalability issue on a 10-core CPU?

    - by JackWM
    I am tuning the performance of parallel Java programs. And want to check the impacts from the Architecture. I'm look into the Intel 10-core CPU, Intel(R) Xeon(R) CPU E7-L8867. I found my program only scales up to 5 cores. What could be the causes? I'm considering the Architecture effects. e.g. memory contention? More specifically, Are the 10 cores symmetric to each other? How many memory controllers does it have?

    Read the article

< Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >